Skip to end of metadata
Go to start of metadata


Dec 14, 2018 17:54

W-PA SIP Public Announcer Manual - English

This guide explains how to install and use W-PA SIP Paging Gateway and provides a description of its basic functions.

Available from WMS Version 3.88

Updated: April 2018

Permalink: https://confluence.wildix.com/x/BQAVAQ


W-PA SIP Public Announcer Introduction

W-PA SIP Public Announcer is used to broadcast emergency messages and communication in large environments such as shopping malls, supermarkets, airports, hospitals. The device has 10 Watt audio output and it still allows you to connect external loudspeakers and microphones. It can also act as a relay for activating door release switches or door locks via 1 embedded short-in detect port and 1 short-out control port. See W-PA Datasheet for detailed technical characteristics.

Before using W-PA

Please read the following safety notices before installing or using this W-PA. They are crucial for the safe and reliable operation of the device:

  • Before using the device, make sure that the environment temperature and humidity requirements are within these ranges: 
    • Operating temperature: -30 ~ 70 ℃ 
    • Storage temperature: -40 ~ 70 ℃ 
    • Relative humidity: 10% - 95%
  • Do not put any foreign objects into the ports of the device. It may cause electric shock or injury accident. If any foreign object gets inside the device, please stop using it
  • Do not let non-technical staff to remove or repair the device. Consider that improper repair may lead to injury accident or cause damage of the device

Packing list 

Before you start to install W-PA, please verify that your package contains the following items:

  • 1 x W-PA SIP Public Announcer
  • 1 x ground screw

W-PA Overview

Front panel

1 - PC interface: connect the device to PC (optional)

2 - Ethernet interface: WAN (PoE) port, standard RJ45 interface, 10/ 100M adaptive, it is recommended to use Cat 5 or Cat 5e cable to connect the device to the network

Note: W-PA is powered by the network cable.

3 - Registration/ Network LED: indicates registration, network and call statutes

  • fast blue flashing: network anomaly or SIP account exception
  • slow blue flashing: during a call
  • solid blue: successful registration

4 - Volume - key

5 - Volume + key

6 - Reset key

7 - Speaker output interface: connect external speakers or microphones

8 - Ground screw: connect external parts with metal housing to this interface to prevent static electricity and other interference caused the equipment to work abnormally

Rear panel

1 - Speaker interface: according to the device input voltage adaptive output maximum power; 4Ω speaker, POE / 8W, 12V / 10W, 18V / 20W, 24V / 30W. The greater the horn impedance, the smaller the output power. Suggested wire diameter: 18AWG or larger diameter

2 - Headset interface: connect external headsets or active speakers

3 - LED interface: 5V output, connect an external LED, indicating the network, call and registration statuses

4 - Function key interface: connect switch components to this interface

5 - MIcrophone interface: it is recommended to use an electret condenser microphone (sensitivity: -38dB, bias voltage: 2.2V) and connect it with a shielded cable to the grounding screw to improve anti-interference

6 - Switch input interface: connect emergency switches, door sensors and other switch components to this interface

7 - Switch output interface: corresponds to the short-circuit input interface, allows to control electric locks, alarm lights and other equipment

8 - Power input interface: 12~24V 2A input, according to the input voltage, determine the maximum W-PA output power amplifier

Note: a power adapter is optional and used for power supply of any external connected equipment.

Installation of W-PA SIP Public Announcer

Connecting W-PA 

  • Use five or super five network cable to connect your W-PA to the network
  • Connect the cable to WAN (PoE) port 

Provisioning of W-PA 

Wildix supports different provisioning modes:

  • WMP provisioning: (the simplest mode) can be applied also for Cloud PBX and for connecting remote devices (assign devices to the PBX from the Portal)
  • Auto-provisining: for local devices (cannot be used for Cloud PBX and for remote devices behind NAT / Firewall)
  • Remote provisioning: this mode can be used for Cloud PBXs and for connecting remote devices behind NAT / Firewall

Refer to the chapters WMP Provisioning and Auto-provisioning of the guide Provisioning of Wildix devices for WMP and auto-provisioning details.

Refer to the chapter W-PA provisioning of the guide Remote provisioning of Wildix devices for remote provisioning details.

Assign to user

To assign a user to your W-PA SIP Public Announcer:

  1. Go to WMS -> Devices 
  2. Choose your W-PA from the list of available devices and click Assign to user
  3. Enter the extension number of a user you want to assign the device to

Note: you can assign W-PA to an existing user or create a new one in WMS -> Users.

Note: In case you have configured failover PBX for your main PBX, the W-PA will have 2 SIP accounts.

Public Announcer function

Once the device is installed and configured, you can use it as a Public Announcer for broadcasting purposes.

Note: to use your W-PA for broadcasting purposes, any external speakers/ microphones should be connected to the device.

To broadcast a message via W-PA:

  1. First, you need to set up a Dialplan to enable the device to answer calls automatically. For this purpose, use Intercom/ Paging group Dialplan. The detailed information about Dialplans can be found here: Dialplan applications Admin Guide

    Note: W-PA SIP Public Announcer supports Paging over RTP multicast. Consult Paging Admin Guide for detailed information.

  2. After you set up a Dialplan, you can call the extension number you've assigned the device to from any Wildix IP phone/ Collaboration/ Mobile app

  3. W-PA will auto answer and play back your voice over connected speakers/ a microphone 

  4. If you want to finish broadcasting, press a Hang up button on the device you use for placing a call to hang up

Ringtone Amplifier function

Starting from W-PA firmware version 2.1.1.3664, the device can be used as a ringtone amplifier.

Proceed with the following:

  • Assign W-PA to a user (Consult Assign to user section)
  • Each time the user receives a call (Collaboration/ WP4X0/ Vision/ W-AIR Handsets/ Android, iOS apps), W-PA simultaneously plays back an amplified ringtone 

Factory reset

In case you need to reconfigure your W-PA, you should perform a reset procedure.

To restart and restore the factory settings of W-PA SIP Public Announcer:

  • Press the Reset key with a paperclip and hold it for 3 seconds

Appendix 1: W-PA Intercom function

Additionally, W-PA SIP Public Announcer can be used as the intercom system for unlocking doors. For this purpose, you need to connect and configure external switch components. You can connect such switch components as door release switches, door locks, intercom panels etc.: 

The intercom function itself is implemented by placing calls from/ to the connected switch components.

Connection of switch components


1-4 - Connect an intercom panel to Speaker, LED, Function key and Microphone interfaces 

5 - Connect a door release switch to Switch input interface

6 - Connect an electric lock to Switch output interface

Switch components configuration

Configure Function keys to be able to place calls from/ to connected switch components:

Note: you can set up only 2 Function keys: "Colleague" or "Speed Dial".


  1. Go to WMS -> Users
  2. Select the W-PA user and click Edit preferences 
  3. Go to Settings -> Function keys and click Edit
  4. Click + to add "Colleague" or "Speed Dial" Function key and enter extension numbers 

    Important: W-PA uses only first 2 Function keys. In case you have other Function keys set up in the first 2 lines, please change their order:



  5. Click Save

Note: you can also set up Function keys in Collaboration -> Settings -> Function keys.


After you set up Function keys, you can move on to the next section.

Placing calls

Unlocking doors with an incoming call

To unlock the door with an incoming call to W-PA:

  1. Call the extension number you've assigned the device to from any Wildix IP phone/ Collaboration/ Mobile app
  2. Use DTMF code 11  to open the door
  3. Press a Hang up button on the device you use for placing a call to hang up

Unlocking doors with an outgoing call

To unlock the door with an outgoing call from W-PA:

  1. Press the connected switch component, for instance, the door release switch
  2. A call will be placed to one of the extension numbers set up in Function keys section
  3. A user who receives a call uses DTMF to enter 11 code to unlock the door
  4. To hang up a call, press a Hang up button on the device you use for placing a call


Not finding the help you need?
Join the Facebook group to ask a question!
facebook_tech-wizards

  • No labels